Gigabyte GIGAFAST GE 2000-N Manuel d'utilisateur

GE 2000-N User Manual (64 bit Gigabit Ethernet PCI Adapter) 1

A:\WIN95 (for Windows 95 osr2) . 3. Win98 SE/Win ME/Win95 osr2 will appear some messages to insert Win98 SE/Win ME/Win

Install on Microsoft Win 2000/ XP Step 1: After booting the Windows 2000, go to Control Panel and access Add/Remo

Click Next. Step 4: Select Yes, search for new hardware. Click Next. Step 5: Your system is now detecting for the presence of new hardwar

Step 6: Select Have Disk …. and access the Windows 2000 driver on the diskette (A:\Win2k_XP\net83820.inf) 13

Step 7: The correct device name appears on the list. Click Next. Click Next to finish driver installation. 14

Verifying your Windows 2000/ XP driver installation Step 1: Go to Control Panel/System. On the System Properties sheet, click the Hardw

Installation on Netware 5 NETWARE Driver Installation Follow this sequence for installation under NETWARE. Install the NIC into a PCI slot o

CFLAGS of the Makefile. 4. After the dpm.o ( The driver module ) is made, to load the driver execute the command "insmod dpm". We can uload

ifconfig <interface-name> mtu <mtu-size> eg: ifconfig eth0 mtu 3000 The BUF_SIZE_MAX value in nsm.h (Tunable parameter) should be cha

Appendix A: Frequently Asked Questions (FAQ) Q: How do I check to see if the network card was installed properly? A: If the card was installed pr

Copyright The contents of this publication may not be reproduced in any part or as a whole, stored, transcribed in an information retrieval system, t

You should be in MS-DOS prompt, enter the word ping, and a space and then the IP address that you assigned to the network card. Hit the Enter key on

Q: I have specified the location and Windows still can’t find the driver under those folders, what now? A: If the location was specified and still ca

Q: Can I directly connect my GE 2000-N to another network adapter on a different computer to do a pier to pier connection? A: To accomplish this, y

Q.: If there is a problem where your MAC Address is all 0’s For NT system: (Win NT, Win 2k and Win XP) 1) 2) 3) Install Gigabit NIC first Device Mana

Appendix B: Cabling and Pin Assignment RJ-45 There are different grades, or categories, of twisted-pair cabling. Category 5 is the most reliable an

Connection between NIC card and Hub In a straight-through cable, wire 1, 2, 3, and 6 at one end of the cable are the same as wires 1, 2, 3, and 6 at t

Appendix C: Technical Information Standards: Compliant with IEEE802.3 10 Base-T / IEEE802.3u 100 Base- TX / IEEE 802.3 ab 1000 Base-T Connecto

FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the

Table of Content: Chapter 1... 5 Introd

Chapter 1 Introduction Congratulations on the purchase of this 64 bit PCI Gigabit Ethernet adapter. High speed broadband internet is commonly used

Package Content • (1) One Gigabit PCI Ethernet Adapter • (1) Driver Floppy OR Driver/Compact Disc With User manual included equirements R • A

Wire Diagram This is a sample of how the card should be placed on your PC case. The Ethernet cable goes into the port shown in the picture after th

Chapter 2 Hardware Installation This section describes the installation of the GE 2000-N card into a personal computer (PC). To instal

5. Insert the GE 2000-N card into the empty PCI slot in the PC. Orient the card so that the RJ-45 connector points out of the computer Warning: The